Parametric things. Tweak. Render. Print.

Parametric Gridfinity bin: pick a footprint, height, compartments, and base options. Snaps onto any standard 42mm Gridfinity baseplate.

Six-cell tote for 50 mm spray cans. Drainage base plate, semicircular carry handle, kid-safe filleted edges.

OpenGrid wall cradle that stands a 4th-gen Apple TV HD (98x98x35mm) on edge, flat against the panel, so it protrudes only ~45mm — low enough to tuck behind a wall-mounted TV. Slide-in cradle: shelf on the plate's bottom edge, two side rails with 45deg retaining lips, open top. The port edge faces down, so plugs drop through the shelf's cable cutout; two back lands hold the device off the plate for a full-height air channel, vented through one big gabled plate window that doubles as the lightening cut. Four corner-tile directional snaps on a 4x4-tile plate, strong nub up. Load it at the bench (tilt the bottom edge in, rock the top back behind the lips) before snapping it to the panel. Prints STANDING on the plate's bottom edge — 9x less overhang than lying snaps-down, and no support scars on the panel-mating face; the only supports are under the four snaps.

Open-front C-ring cradle with a Multiboard snap-slot backer. Takes any cylinder; the ring, wall, and slot region all flex on sliders.

Ego MultiHead EA0820 edger attachment wall mount converted from screw-mount to openGrid: the operator's bracket mesh import()ed as-is, its four countersunk screw holes plugged solid, and ten directional openGrid snaps (strong nub up) fused to a grid-aligned extended back plate. Prints supportless snaps-down — snap the two breakaway ribs out of the tool slots before first use. Hangs the EA0820 edger head by its original slot bearing surfaces.

Ego LB6500 leaf-blower wall bracket converted from screw-mount to a wall grid: a native parametric remodel of the original bracket (bearing surfaces held to <1mm of the source mesh) fused to the selected back mount — a 5-slot Multiconnect backer (slides down onto wall connectors, load seats into the slot domes) or 8 directional openGrid snaps with the strong nub up. Exports one STL per mount_type.

Ego Power+ powerhead wall holder converted from screw-mount to openGrid: the operator's holder mesh import()ed as-is, its four countersunk screw holes plugged solid, and eight directional openGrid snaps (strong nub up) fused to a grid-aligned back plate. Prints supportless snaps-down — snap the four breakaway ribs out of the shelf notches before first use. Hangs the powerhead by its shaft on the original fork and shelf bearing surfaces.

Wall cradle for a 51×84×7mm LED-strip remote. Open-front pocket with 45°-chamfered retaining lips and a thumb scoop, on a selectable back mount — a 2×3 grid of openGrid snaps on 28mm pitch or a Multiconnect slot backer for Multiboard rails (slides down onto wall connectors, weight seats into the slot domes). Prints mount-down, support-free; exports one STL per mount_type.

OpenGrid wall cradle for a 55×124×7.7mm LED-strip remote. Same design as the 51×84 twin with a selectable back mount — a 2×4 openGrid snap grid (default) or a Multiconnect slot backer for Multiboard rails; the plate is capped at 116mm so the remote stands ~10mm proud for easy grabbing. Exports one STL per mount_type.

Open-topped wall bin sized in 28mm grid units so it aligns with the tiles. Fused to the selected back mount — one directional openGrid snap per tile (strong nub up for the cantilever load) or a Multiconnect slot backer for Multiboard rails (slides down onto wall connectors, load seats into the slot domes). Full-height sides, 45° scoop front lip, rear floor fillet; prints mount-down, support-free. Exports one STL per mount_type.

Handheld alignment tool for installing openGrid panels: a stiff plate with a 2×2 array of openGrid snaps on 28mm pitch on one face and a domed grip knob on the other. Prints snaps-down with zero supports — the knob's cylinder-plus-dome profile has no overhang anywhere.

Ready-to-print openGrid snap connectors (28mm pitch). One STL per variant: lite/full depth x directional/bidirectional. Press straight into an openGrid board.

Shoulder saddle pair for hanging a Ryobi ONE+ P2860 backpack sprayer by its padded straps on an openGrid wall — print one left and one right. Crowned 42mm prong with a 55mm saddle dip and 12mm retention lip seats an 80mm strap exactly as it drapes on a shoulder; directional snaps put the strong nub up. Empty-sprayer duty (~7kg total), snaps-down zero-support print.

Friction-fit childproof cover for the speed-adjust knob on a KidsCleanCar kids' ride-on. Slips over the 48.1mm lower flange and grips it with tunable internal crush ribs, spinning free over the knob so a toddler can't change the speed while a straight adult pull lifts it off. Original design; no vehicle modification, fully reversible.

Rounded bullet stylus for kids' pressure-sensitive LCD drawing pads. ~2 mm dome tip, no hard edges, prints tip-up with no supports.

Hex-profile stylus for kids' pressure-sensitive LCD drawing pads. Pencil-style anti-roll hexagon body with every edge filleted, ~2 mm dome tip, prints lying flat on a hex face with a built-in breakaway support fin under the tip.

Wall-mounted holder for Little Tikes Dream Machine cartridges and figures — an openGrid tray sized in whole 28mm cells that auto-fills with 51x14 cartridge slots (top) and rounded figure pockets (front). Pick a back-face mount: openGrid lite snaps (default), a blank flat back, or openConnect receivers — all on the same 28mm cell grid. The preview shows a compact 2x4-cell tile; scale the cell count up to 9x8 for the full-size holder.

Cartoonish popcorn kernel. Smoke-testable glyph with a handful of dial-your-shape parameters.

Under-bib drip deflector for Aquor hose bibs. VHB-mounts to the face-plate underside and kicks freeze-drain water outward, clear of the wall.

Captive bench mount for a Blu Technology 3-way black-tank flush valve. Asymmetric saddles clamp the two inner fittings (31.5mm left, 29.25mm right) across a 37mm gap; vertical exclusion cylinder carves cap clearance for the T-handle's 90° swing. 4× M3 SHCS into heat-set inserts.

Captive bench mount for a Blu Technology digital flow meter (27mm × 80mm pipe). Two split-saddle pairs clamp the bare bands at each end of the meter; the middle 44mm gap leaves the LCD display saddle free. 4× M3 SHCS into heat-set inserts.

Floor foot for an 8" × 17" BluTech RV water softener (~20 lbs full). Open-bottom ring cradle grips the cylinder bottom laterally at 85mm — cylinder drops through and rests on the RV floor, lifts straight up for maintenance. Six radial gussets transfer load into a continuous flat VHB-bearing annular flange; scupper notches at the base drain water laterally without breaching the bond face.

Vendored MakerWorld Disney ear hanger — wall-mount clip for Mickey/Minnie ear headbands. Original by an upstream MakerWorld author; see the file header for attribution.

Side-mount holder for the goBlu 3-cylinder RV water filter assembly. Three flush-touching pods cradle 90mm filter housings; flat back face VHB-mounts to the RV wall.

Adapter plate that covers a 235mm (9.25") RV ceiling speaker cutout and mounts a WiFi access point in its place. Self-centering recessed cup nests up into the hole, 270mm one-piece flange (H2S bed) screws to the ceiling with 6 countersunk #6 screws, and a 100mm boss carries 4× M3 heat-set inserts on an 82.16mm bolt circle for the AP bracket, plus off-center arc-slot cable pass-throughs on the insert axes that line up with the bracket's offset wiring openings (its center hub is solid). Prints room-face-down with zero supports.

US electrical box extension ring that builds out a 1-4 gang box flush with a thick wall. Ports a proven MakerWorld design: rounded rect_tube shell with per-gang screw posts on the standard US box hole spacing.